Jan 24, 2020
College of Engineering and Computer Science
Department of Industrial Engineering and Management
Systems, Engineering II, Room: 312
Jacob Lawhon, Jacob.Lawhon@ucf.edu, 407-823-5021
Dr. Luis Rabelo, Luis.Rabelo@ucf.edu
- Students wanting to declare a major in an engineering discipline must be in good academic standing and must have a “C” (2.0) or better in each of the following courses or their equivalents: MAC 2311C , MAC 2312 , PHY 2048C , and CHM 2045C or CHS 1440 .
- Students wanting to declare a major in an engineering discipline must complete a change of major in the term of completion of the final pending prerequisite course(s) listed above.
- Each engineering student is assigned a qualified engineering academic advisor in the department of his/her major. Each student should seek academic advisement before registering for classes each semester to minimize excess hours and to ensure that satisfactory academic progress is being maintained.
- Students in the Industrial Engineering major are expected to make consistent good progress toward their degrees to remain enrolled in, or eligible for, any major in the College of Engineering and Computer Science (CECS) or the College of Optics and Photonics (COP). Therefore,any student majoring in Industrial Engineering who repeats any UCF course and does not earn a grade of “C” (2.0) or better on the second attempt will be placed on Lack of Progress Probation and remain on Lack of Progress Probation as long as the student is enrolled in a CECS or COP major. If a student on Lack of Progress Probation does not receive a grade of “C” (2.0) or better by the third attempt in the same UCF course, the student will be excluded from all CECS and COP majors. Any student majoring in Industrial Engineering who has accumulated 7 or more unsuccessful attempts (i.e., grades below “C” (2.0) and withdrawals) over all courses taken at UCF will be placed on Lack of Progress Probation and remain on Lack of Progress Probation as long as the student is enrolled in a CECS or COP major. If a student on Lack of Progress Probation has a tenth unsuccessful attempt over all courses taken at UCF, the student will be excluded from all CECS and COP majors.
- A student who is excluded from CECS and COP majors may seek readmission to a major in CECS or COP after at least one full year has passed since exclusion. Readmission is not automatic and is dependent upon a high probability of success after readmission. Any student who is readmitted to the Industrial Engineering major will be subject to all probation conditions that applied at the time of exclusion.
General Education Program (GEP) (38 Credit Hours)
- The UCF General Education Program (GEP) is described in the section, General Education Program, found elsewhere in this catalog. Engineering students should closely study the requirements of the UCF GEP and the allowable substitutions detailed in paragraphs A. through E. below to minimize excess hours. Students transferring to UCF from within the Florida College System or State University System should complete the GEP and the Common Program Prerequisites before transferring.
Communication Foundations (9 Credit Hours)
Cultural & Historical Foundations (9 Credit Hours)
Mathematical Foundations (7 Credit Hours)
Social Foundations (6 Credit Hours)
Select One: (3 Credit Hours)
Science Foundations (7 Credit Hours)
Common Program Prerequisites (CPP) (19 Credit Hours)
These courses are specifically required for all engineering students of the Florida State University System. CPP courses are also available at other Florida postsecondary schools and may be transferred directly to UCF programs. A 2.0 cumulative GPA or better is required for those courses in this section.
See “Common Prerequisites ” in the Transfer and Transitions Services section for more information.
1 A 2.0 cumulative GPA or better is required for this course.
Select One: (4 Credit Hours)
Core Requirements: Basic Level (2 Credit Hours)
Engineering Core: Basic
The College of Engineering and Computer Science requires all engineering students to achieve a minimum 2.250 GPA in completing the core courses required for the major, together with the restricted electives and senior design courses listed below.
Core Requirements: Advanced Level (60 Credit Hours)
Courses Required for the Major (60 Credit Hours)
The Industrial Engineering and Management Systems department requires all students within the major to achieve a “C” (2.0) GPA or better in all courses in this section with a prefix of EIN, EGS, ESI, STA and MAS.
1 Courses with significant programming content in C, C++ or Java may be used to satisfy this requirement but must be approved by the IEMS undergraduate coordinator.
Restricted Electives (5 Credit Hours)
- Technical electives are available in the BSIE program to address specific student interests in a variety of technical areas. Students should consult with their assigned academic advisor for a list of the approved technical electives and the terms when specific courses of this type are to be offered.
Capstone Requirements (4 Credit Hours)
Foreign Language Requirements
- Two years of one foreign language in high school, or one year of one foreign language in college (or equivalent proficiency exam) prior to graduation.
Departmental Exit Requirements
University Minimum Exit Requirements
- A 2.0 UCF GPA
- 48 semester hours of upper division credit completed
- 60 semester hours earned after CLEP awarded
- 30 of the last 39 hours of course work must be completed in residency at UCF.
- A maximum of 45 hours of extension, correspondence, CLEP, Credit by Exam, and Armed Forces credits permitted.
- Complete the General Education Program, the Gordon Rule, and nine hours of Summer credit.
Total Undergraduate Credit Hours Required: 128
Honors In Major
- Engineering Leadership Certificate
- Engineering Leadership Minor
- This Industrial Engineering program has potential ties to professional licensure or certification in the field. For more information on how this program may prepare you in that regard, please visit http://www.iems.ucf.edu/undergraduate/prospective
- Courses transferred must be formally evaluated for equivalency credit. The student must provide all supporting information with his/her petition for this evaluation.
- EGS 1006C and EGN 1007C are required courses for incoming freshmen only. The credits for these two courses (one hour each) may, with prior approval of the department academic advisor, be moved to area 5. Restricted Electives.
Acceptable Substitutes for Transfer Courses
Program Academic Learning Compacts
- Part-Time Student: $38 per term
- Full-Time Student: $77 per term
Plan of Study (128 Credit Hours)
- Tentative Course Schedule for Entering Freshmen: The tentative course schedule listed below is a guide for those students who plan on completing their degree in four years. All engineering students should meet with their faculty advisor to develop and maintain an appropriate plan of study.
Freshman Year - Fall (12 Credit Hours)
Freshman Year - Spring (12 Credit Hours)
Freshman Year - Summer (9 Credit Hours)
Select One: (3 Credit Hours)
Select One: (3 Credit Hours)
Sophomore Year - Fall (14 Credit Hours)
Sophomore Year - Spring (13 Credit Hours)
Sophomore Year - Summer (10 Credit Hours)
Junior Year - Fall (13 Credit Hours)
Junior Year - Spring (12 Credit Hours)
Junior Year - Summer (9 Credit Hours)
Senior Year - Fall (12 Credit Hours)
Senior Year - Spring (12 Credit Hours)